Vehicles
97 not categorized PORSCHE BOXSTER RUBBER BUSHCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.150PB100915 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$47.30
Make a selection 90162892400 This is the male bushing of the two required per wiper rack. easily installed with the wiper arm and nut removed. View/Change Diagram
From $9.21
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 150PB100919 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 477411313B Rear; stock rubber (2 required per car) for 18 mm bar bushing id 15.70mm View/Change Diagram
From $8.12
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection 90133300309B This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car.
$306.90
Make a selection 90162892301 This is the female of the two required bushings per wiper shaft. easily installed with the rack removed. View/Change Diagram
From $15.81
Make a selection 61610754300 Known as: rubber bush View/Change Diagram
From $20.68
Make a selection 901423015RB Tried to dismantle your pedal cluster to install new bushings and found that it is impossible to drive out the roll pin? Join the crowd! Time for a rebuilt cluster. All of our rebuilt clusters are completely dismantled, sand-blasted, painted, new parts used if needed, and reassembled with silicone bronze bushings. the only complete cluster available from anywhere! Includes brake light switch, brake push rod, throttle pivot, and rubber pedal pads. Ready to be installed! core charge...(choose a part on the right to read more) General Fitment914 1970-76911 1965-69 930 1975-77 911 1974-77 911 1970-73 912 1965-69
$425.00
Make a selection 91133300905 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
From $273.90
Make a selection 91133300900BHD Bushings set with instructions:w/ 80-85 shore a hardness
$29.89
Make a selection 91133300902 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
$363.00
Make a selection 96434101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$49.50
Make a selection 95534124204
View/Change Diagram
From $10.00
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$205.00
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 96437505580 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Be sure to swap yours out during the next service. Sold individually. Central fitment into the transmission carrier bracket. 1 qty. Required. Tech tip: tech tip: the bushing should be mounted with the 2 openings on the vertical plane. Now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 964 rs 1 qty. Hex head...(choose a part on the right to read more) View/Change Diagram
$148.50
Make a selection 993014340 Your suspension is only as good as the bushings. Over time, factory rubber bushings deteriorate, allowing the suspension to become loose and sloppy. Daystar poly graphite bushings last years longer than standard bushings, and bring back suspension performance. Available in performance, which are much stiffer and race-ready. Set of 4 bushings for the front and rear of the front a-arms. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 912 1965-69 914 1970-76
$31.89
Make a selection ER2221800 Elephant racing monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! These proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around unpredictably. The sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike poly bushings that bi...(choose a part on the right to read more) General Fitment944 1982-85924 1976-79 924 1980-85 924 1986-88 944 1985-88 944 1989-91 968 1992-95
$350.00
Make a selection 99333105200 The bushings are made of rubber with a 65-shore hardness value, which is more comfortable for street use. Sold individually. View/Change Diagram
From $823.90
Make a selection 91133300900B Bushings set with instructions:w/ 55-60 shore a
$29.89
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |